One Piece Mask Pattern and Tutorial

UNADJUSTEDNONRAW_thumb_4c0d.jpgThis will be the basis for the vacuum cleaner bag pattern, but THIS mask can be made now, with cotton (for maximum laundering potential) to use as a stand-alone community mask, or as an N95 mask cover to help extend the life of masks for medical personnel.

The vacuum bag pattern will not be sewn.

Sewing through a vacuum bag destroys its structural integrity by introducing around 200 .5mm to .7 mm holes into fabric that’s supposed to filter down to .01 microns. A millimeter is 1000 microns, so a hole .5 mm wide permits 50,000 .01 micron particles to march through abreast. Don’t do it!

Do not waste bags learning this, because the supply chain for vacuum bags is smaller than the supply chain for medical masks and construction masks.

This also applies to any medically recommended fabric, like surgical drapes. Don’t put holes in them unnecessarily. If your hospital system is asking for sewists to make masks from drapes, follow their directions precisely.

And if you notice something is wrong, like they’re asking you to poke holes into mask fabric, speak up! Just because a doctor is an expert at medicine doesn’t make them an expert in materials science! They’re tired, they’re overworked, so be their extra eyes and safety check.

The vac bag mask will be up as soon as I’ve got durable adhesives. But do not sew them. Do not. There is no safe way to sew them, and this is not a case of the perfect being the enemy of the good. It’s destroying a potentially lifesaving material through not understanding it, and giving the medical workers using them a false confidence in a material that will not protect them. 

These one piece masks will fit OVER an N95, which keeps the N95 cleaner and allows them to be used longer. The fit will be tight, but all masks should fit tight, because a loose mask leaks air.

Multiple layer cotton masks will filter around 70 percent of aerosolized particles and are sufficient for community protection. This is considerably more protection than being barefaced. 

Drafting the Mask pattern

This is the image for the pattern. You can download it and print it at 100% scale. 

UNADJUSTEDNONRAW_thumb_4c09.jpg

With a caveat: your printer will probably cut the edges of the image off. For the most part this doesn’t matter — just use a ruler and continue every line to the edge of the paper, then cut out the triangle.

Or you can draft the pattern relatively quickly. This time, we’ll use use the 8.5″ x 11″ measurements. The A4 metric process is similar, but the measurements differ.

You will need:

  • A sheet of copy paper
  • A precise ruler
  • Pencil and eraser (sharp mechanical is best)
  • A protractor or a quilting ruler with the 45° angle marked is useful, but not essential.

 

Orient a piece of 8.5 x 11 inch sheet of paper in LANDSCAPE in front of you, so it is wider than it is tall.

UNADJUSTEDNONRAW_thumb_4bdc.jpg

Draw two lines, bisecting the paper: one from the middle of the long edge to the middle of the opposite long edge, and one from the middle of the short edge to the middle of the opposite short edge. The middle of the long edge is 5.5 inches from a corner; the middle of the short side is 4.25 inches from a corner.

UNADJUSTEDNONRAW_thumb_4bb9.jpg

At the top of the page, draw a line along the long edge ⅝” inch from the edge. This is your seam allowance.

Repeat at the bottom edge.

UNADJUSTEDNONRAW_thumb_4bd9.jpg

On the horizontal middle line, measure 2.5  inches outwards from the center (where the middle lines cross.) Make a tick mark, A. Repeat for the right side. Mark that one B.

UNADJUSTEDNONRAW_thumb_4be9.jpg

Measure 1 inch up from the bottom left corner of the page, on the left edge. Make a tick. Label this one C. Repeat for the bottom right edge; label this one D.

Measure 1 inch down from the top left corner, on the left edge. Make a tick. Label this one E. Repeat for top right corner; label this one F.

UNADJUSTEDNONRAW_thumb_4bc9.jpg

Draw a straight line from tick A to tick C.

Draw a straight line from tick A to tick E. 

Draw a straight line from tick B to tick D.

Draw a straight line from tick B to tick F.

Check your angles. The angle ACE should be 94°  at A, and 43° at E and A. Also for triangle BDF.

UNADJUSTEDNONRAW_thumb_4bc0.jpg

Measure ½ inch inwards from the left upper corner of the paper. Draw a straight line down to the angled line. Repeat for each corner — this is fold over seam allowance for casings.

Cut out the triangles ACE and BDF.UNADJUSTEDNONRAW_thumb_4bfd.jpg

UNADJUSTEDNONRAW_thumb_4bec.jpg

This is the shape of the pattern.

Each mask requires at least TWO of these.

These are much easier 3 and 4 layer masks than pleated masks.

If you are in the A4 paper world, draw the center lines, but adjust the measurements:

Tick marks A and B are 7.5 cm from the center. C, D, E, and F are 3 cm from the edge. G, H, I and J are 5 cm from the center line.

All seam allowances are 1 cm. Your angle will be slightly off of 90°  and your mask will be a little longer and narrower, but if you ensure your angles match on both sides of the center line, the mask will be fine. 

Construction

Cut at least 2 pieces from your fabric. UNADJUSTEDNONRAW_thumb_4c03.jpg

Fold the casing hems towards the center; press. UNADJUSTEDNONRAW_thumb_4c1a.jpg

Stitch down all four on each piece of fabric.UNADJUSTEDNONRAW_thumb_4c19.jpg

Lay at least 2 pieces together, right sides together, wrong sides out.

If you’re using 3 layers, it’s right side up,  doesn’t matter, right side down. If you’re using 4 layers, it’s right side up, doesn’t matter, doesn’t matter, right side down.

UNADJUSTEDNONRAW_thumb_4bef.jpg

Stitch both long sides with a straight stitch, using a ⅝”/ 1 cm seam allowance.

UNADJUSTEDNONRAW_thumb_4be4.jpg

Place a pair of twist ties, a piece of pipe cleaner, 4 inches of coated copper wire, or 4 inches of brass or copper jewelry wire on the top seam allowance, matching the center of the mask to the center of the wire.

UNADJUSTEDNONRAW_thumb_4bfa.jpg

Zigzag over the wire. Repeat for the bottom edge. Turn right side out, press the seams. Now this mask can be worn in either orientation.

UNADJUSTEDNONRAW_thumb_4c18.jpg

Stitch down the long sides again, using a ⅝”/1 cm seam allowance. This is the casing. (Sorry, this picture is out of order. This step can be done at any time after this point.)

UNADJUSTEDNONRAW_thumb_4c0f.jpg

Fold the bottom up to the top, on the center line, with the side you want out to the world on  the inside. The two angled edges should meet. (You can wiggle these a little. Fabric is forgiving.)

UNADJUSTEDNONRAW_thumb_4c1b.jpg

Set your sewing machine to a 4 mm wide, 1.5 mm long zig zag (or a wide, fairly tight zigzag if your machine doesn’t speak metric)  and sew both angled edges near the raw edge. Do not sew over the folded edge of the casings.

 

UNADJUSTEDNONRAW_thumb_4c1c.jpg

Turn right side out, thread twill tape, elastic or fabric ties through the casings, or proceed to the Jersey headband instructions. Trim any dangling threads.

The one piece mask is finished. UNADJUSTEDNONRAW_thumb_4c02.jpg

4 thoughts on “One Piece Mask Pattern and Tutorial”

  1. Hello and thank you so much for the duckbill mask pattern. When I compared your pattern to my Halyard N95 Fluidshield size regular mask, your pattern is 1 inch wider ear-to-ear, wider at the nose pocket by 1 inch, and the same height. If sizing down, I suggest changing the widths and maintaining the distance from long edges to center. A small Halyard mask is about the same step-down in width, with a slightly shorter height. The difference in height makes little difference to the fit because it simply elongates the duckbill for a cloth fabric. However, adjusting height could make a difference on fit with stiffer materials if sizing the pattern.
    Also, if anyone is making this as a cloth fabric mask, without trying to cut a HEPA fabric, the symmetrical pattern can be cut on the fold so that the angles are easier to cut. (If you said that in your tutorial, I missed it.) I made a second pattern piece to allow adding disposable filters to my cloth duckbill masks.
    The stretch Jersey band is a great addition! If you don’t know who you are sizing the mask to fit, cloth or twill ties might achieve a better fit for some people with larger or smaller sized heads. Folks who wear glasses do better without ear loop styles, imo, so any suggestion for alternatives is welcome!

  2. I’m having trouble getting my mask with the right side turned out and the seams inside. What am i missing?

    1. If you’re using two layers, then the front sides of your fabric need to be together when you sew them.

      If you’re using 3 layers, pretend two layers are one piece. (You can stitch them together, with both top sides up, or stick them together with glue stick — it washes out!) Then make sure the front sides are together, and stitch.

      If you’re using 4 layers (and this is going to get really uncomfortable as the weather warms, so maybe not?) stack them in two stacks with all of the front sides up, treat each stack as 1 piece, put the fronts together, stitch.

  3. One thing I’ve found useful, is to use an elastic headband on the bottom, and then shoelace on for the top tie. That way you can hang it around your neck while in the car, and then just pull it up and tie when going into the store (for example). I do like the metal in both top and bottom, so it doesn’t slip off when talking. Not sure of how to attach a picture here, but i have them if you need to see what i’m talking about. Thank you so much!

Leave a Reply to CZed Cancel reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s